I have just what you need for a Dutchmen Four Winds 31B-DSL, the Trailer Hub and Drum Assembly part # 8-407-5UC3-EZ and Dexter Electric Trailer Brake Kit part # K23-462-463-00 are both correct, bolt-on replacements. The hubs are 6-lug and the brakes are 10". view full answer...
You will need a minimum of 3 inches, it is best to install the Solera RV Slide-Out Awning, # LCV000165062, in the 3-6 inch range above the slide out for proper clearance and angle, above 6 inches becomes to steep. Please note the attached installation video for additional valuable information. view full answer...
The overall dimensions of the Valterra Frame Assembly and Glass # A77051 are 15-3/4" wide x 24-3/4" tall. Just the frame is part # A77008 and those are the dimensions for just that. view full answer...
The correct size Adco Olefin All-Climate + Wind RV Cover for a 2008 Dutchmen DSL 30S can be had with part # 290-34846. This is the only cover on the market with an Olefin top which blocks UV-Rays. If you live in a southern climate this will be a must. view full answer...
According to my research you should have 3,500 lb axles on your 2013 Dutchmen Model 261BHS which means you need the following:
- Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles # AKHD-655-35-EZ-K (Need Qty 4)
- Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA (Need Qty 2 since these are a set)
If you have a different setup please let me know so I can make a different recommendation for you! view full answer...
Without knowing your particular setup on your Dutchmen Travel Trailer, the best way to determine your inner bearings is to pull the remove the hubs and find the number on the bearing itself. You can also measure the spindles where the bearing sits. In many cases, there can also be an axle tag on your axle beam that tells you information about the spindles you have.
I went ahead and attached a chart that shows the measurements you need to help determine your bearings. The best way to get... view full answer...
The correct braking assemblies will be the Dexter Nev-R-Adjust Electric Trailer Brake Kit part # K23-478-479 and the correct hubs/drums will be the Dexter Trailer Hub and Drum Assembly part # 84656UC3-EZ. I called Lippert and confirmed these as fits for a 2012 Dutchmen Classic 276RBS. view full answer...
If you are referring to the Lippert Electric Trailer Jack with Footplate part # LC285318 then you are going to want to use the Replacement Extend / Retract Switch Assembly part # LC226023. In order to replace the switch you will need to obtain a pick tool or very small flathead screwdriver and beging to pry the top or bottom of the switch out of the housing. Once this is done you can then remove the spade terminals and install them on the new switch. In order to install the new switch you... view full answer...
We do not have a list of parts used on your Dutchmen Aerolite trailer so to determine the correct replacement parts for your trailer it will require some measuring and examination of existing parts.
The fan motor is likely going to be # BVD0218-00 because this motor is now used as the replacement for most old and new Ventline roof vents. But you can check the motor on your vents now for model information and specs and that will help.
The cover or lid itself could be one of several designs.... view full answer...
Yes, you could use the wire circuit "auto antenna" of the Furrion RV Stereo # DV1230BL as a remote 12 volt power source to turn on your amp. view full answer...
I was able to find a picture of the part number 90110 C1 that you need and found that the exact replacement is the # BV0554-03 that you referenced. If you wanted white instead you'd want # BV0554-01. view full answer...
The water heater that I recommend as a replacement for your Atwood G6A-7 that will give you the best bang for your buck is absolutely the tankless option water heater from Fogatti, and you can choose from either White or Black in color:
- White: Fogatti RV Tankless Water Heater # LSB64FR
- Black: Fogatti RV Tankless Water Heater # LSB44FR
The Fogatti water heaters fit a 13" tall x 13" wide x 17-3/4" deep cut out, so you shouldn't have any problem fitting them in the same space as the... view full answer...
Since your vent cover goes up higher than the MaxxAir II RV and Enclosed Trailer Roof Vent Cover # MA86JR and you mention the motor on your fan, you most likely need to replace the cover with the MaxxAir FanMate Rain Cover - Smoke # MA00-955003 so you don't burn out your motor or damage your vent. view full answer...
Since your trailer has 12" brakes with a 6-bolt mounting pattern you'll actually need brakes for a 5.2K axle:
- Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-7-SA
The for a tire and wheel combo I highly recommend the following:
- Westlake ST225/75R15 Radial Tire w 15" Liger Aluminum Wheel # LH36FR
This tire and wheel set not only looks sleek but it performs very well and is backed by complimentary roadside assistance for 2 years as well as a 5-Year warranty on the tire and... view full answer...
Most likely the Never Fail Triple Axle Suspension Upgrade Hardware Kit for Double Eye Springs # LC281288 does fit your triple axle 2011 Dutchman Voltage 3900 but to be sure you'd want to take a few measurements of your current setup to verify.
The shackle dimensions are:
(12) 2-1/4" Long shackle straps
(12) 3-1/8" Long shackle straps
Bushing dimensions:
Inner diameter: 9/16"
Outer diameter: 11/16"
Length: 1-5/8"
Suspension bolt length:
2-5/16"
Bolt size: 7/16"-20
Shackle strap thickness:... view full answer...
The Atwood Air Command Rooftop RV Air Conditioner w/ Heat Pump # AT15033-22 will match up to the duct work on your 2014 Kodiak camper. You will need to use the thermostat that comes with this kit though. You won't be able to reuse the thermostat you have. view full answer...
From that number you supplied, it appears you have axles that are 5,200-lb to 6,000-lb with a 12" - 6 on 5-1/2 bolt pattern. For brake assemblies I recommend # AKEBRK-7R-SA for the right hand side and # AKEBRK-7L-SA for the left. This is a self-adjusting 12' brake assembly, mounting bolts and hardware, # BRKH12S sold separately.
If you do decide you need to replace the hub and drum assembly, I recommend, # AKHD-655-6-K. This is an etrailer replacement hub and drum assembly supplied... view full answer...